How To Repair A Small Hole In A Shingle

Download Article

Download Article

When plastic is punctured, it seems catchy to set up at starting time. Luckily, at that place are ways to set and patch plastic without completely replacing information technology. A makeshift cement from super glue and blistering soda can fill modest holes in a compression. Larger holes in plastic can exist filled with melted plastic or epoxy. No matter which method you lot use, you'll be able to plug the pigsty and pretend it never even existed.

1. 1

   Attach cardboard on the behind of the pigsty. Use a sturdy slice of scrap cardboard that be easily removed later and adhere it with tape or a hand clamp. Placing a back slice backside the hole prevents any material from running through the hole.^[1]

   • If yous cannot fit paper-thin betwixt the plastic, like if the pigsty is in a gas can, this can nevertheless work, merely it may not have as solid of a hold.

2. 2

   Squeeze 3 or four drops of super glue into the hole. Brand a small pool at the lesser of the hole with a few drops of super gum. The bankroll will requite the glue a affluent edge at the lesser of the pigsty. Super gum dries quickly, so you will have to piece of work fast before it sets.^[two]

   • Wear plastic gloves to avoid getting super glue stuck on your hands.

   Advertizing

3. 3

   Sprinkle a compression of baking soda on summit of the glue and press firmly. Press the blistering soda into the super glue with your finger or a flat edge, so the two substances bond together. Super glue is thin, but when combined with a powder similar baking soda, it thickens and makes more than of a cement-similar substance.^[iii]

   • Other powders similar sawdust or chalk powder may also work.

4. four

   Layer super glue and baking soda until the hole is filled. Keep building layers until y'all've formed a plug that is flush with the height of the hole. Even if the hole is filled after the beginning time, add a second layer of super glue and baking soda to strengthen the bond.^[4]

5. 5

   Let the patch dry for 15 minutes. As information technology dries, the hardened substance will be a chalky white color. While information technology is not the well-nigh visually pleasing, it will be stiff and go along the hole closed. One time the patch is dry, y'all tin remove the backing.^[5]

   • Yous tin effort mixing colored powder or food dye with the baking soda to resemble the colour of the plastic more closely.

6. half-dozen

   File the summit of the patch, if there is any residual. Use short back-and-forth strokes to sand abroad any buildup. Go along a constant pressure as y'all file the cement mixture. Sandpaper or a fine-grit metal file will work fine.^[6]

   • Habiliment a face mask and then you don't exhale in any plastic particles every bit yous work.

   Advertizing

1. i

   Adhere a cardboard backing to the hole. Attach the backing with pieces of tape or with a hand clench to foreclose any run-off. Make sure information technology is pressed tight against the bottom of the pigsty. Fleck cardboard works best since information technology tin can easily be removed when you're finished.^[7]

2. two

   Melt a plastic welding rod with a welder into smaller holes. Hold the plastic rod ¹⁄_two inch (13 mm) in a higher place the hole. Use the welder on the finish of the plastic rod to melt the plastic into the pigsty. Once the hole is filled, turn off the welder and let the plastic solidify.^[8]

   • Keep your hands abroad from the heating finish of the plastic welder to avoid burns.
   • Find a rod that closely resembles the colour of the plastic you're fixing.

3. 3

   Wrap a heated plastic rod into a screw inside a larger pigsty. Heat the end of the plastic rod with a plastic welder. Start spiralling the rod along the bottom of the hole and then it is pressed confronting the bankroll. Layer the plastic until it lays affluent with the top edge of the hole.^[9]

   • Hold the plastic welder ⁱ⁄₂ inch (13 mm) away from the rod. You want information technology to be malleable, but non for it to melt completely.

4. 4

   Utilise a soldering iron to trim the rod and smooth the pigsty. One time the hole is filled with the plastic, use a hot soldering fe to cut the end. Rub the edge of the iron across the acme of the filled hole to smooth it out and to fuse the top of the plug.^[ten]

   • Do not leave a depression in the plug, since this could compromise its strength and integrity.

5. 5

   Let the plastic cool for five minutes earlier filing it. It only takes a few minutes for the plastic to solidify. One time it is cool to the touch, use a file or sandpaper to smooth out plastic and make information technology flush.^[11]

   • If you want to get rid of any file markings, hold the plastic welder just above the area to polish it out.
   • Cutting away any large pieces that are too big to file with a pocket-sized razor bract.^[12]

   Advertizing

1. 1

   Cut two fiberglass patches six inches (15 cm) larger than the hole. Get out a picayune extra room on the fiberglass gives you a fiddling jerk room and helps ensure the hole is fully covered. These mesh patches provide an expanse to identify epoxy across the pigsty of the plastic.^[13]

   • Fiberglass patches tin can be purchased at hardware stores or online.

2. ii

   Mix fifty-fifty amounts of each office of the epoxy in a bucket. Use a stirring stick to mix the fifty-fifty parts of the epoxy in a saucepan or large mixing basin. A 2-part epoxy has a resin and an activator that demand to be mixed together to cure. Once it is mixed, it should be very thick and tacky.^[14]

   • Article of clothing dispensable gloves when working with epoxy, since it may cause peel irritation.
   • Lay cardboard or another disposable liner underneath the plastic, in case it drips through the mesh.

3. 3

   Spread a thin layer of epoxy on 1 side of the hole with a putty knife. Encompass the entire expanse surrounding the hole with a layer of epoxy. Make certain the layers are however that it dries evenly. It should be thick enough that the fiberglass can stick to information technology, just not overly thick.^[15]

   • At that place should be enough epoxy so that the unabridged fiberglass patch sticks to the plastic.

4. iv

   Printing i of the fiberglass patches onto the epoxy, so that the hole is in the middle. Utilize your hands to push the fiberglass the hole is in the heart of the patch. The excess fiberglass on each side ensures at that place is enough to cover the hole and volition add a smooth transition between the plastic and epoxy.^[16]

   • Fiberglass patches are flexible and should conform to the shape of the plastic y'all are mending.

5. five

   Paint another layer of the epoxy over the fiberglass. This time as you employ the epoxy, spread information technology over the office of the mesh that covers the hole. Use just enough epoxy to hide the mesh underneath, but not so much that it is clumpy. Yous want information technology to be as shut to flush with the plastic every bit you can.^[17]

6. half-dozen

   Let the epoxy dry out for 24 hours. Allow the epoxy set on one side of the plastic before transporting the plastic or moving on. As information technology dries, information technology volition harden and form a solid layer. It takes at least 24 hours for the epoxy to initially cure, though it may take longer in humid climates.^[18]

7. seven

   Repeat the process on the other side of the pigsty. Once one side of epoxy and fiberglass has prepare, apply epoxy to the other side of the plastic and adhere the fiberglass to it. Paint another layer of the epoxy over the fiberglass and permit it cure for some other 24 hours.^[19]

   • This entire procedure can be washed in one case more than with more fiberglass pieces if y'all need to add more than integrity to the plastic.

8. 8

   Sand the epoxy until it is smooth. Once both sides of the epoxy are ready and dry, you tin can employ sandpaper to smooth any dry out epoxy, so it is level with the plastic. Habiliment a face mask as yous sand the epoxy down so you don't breath any dust particles.^[20]

   • Epoxy tin be painted subsequently to match the colour of the plastic.

   Advertisement

Add New Question

• Question

  What do you lot use to fill holes in plastic?

  

  Drew Hawkins1

  Community Answer

  You actually have a few options. If you're filling smaller holes, 1 simple solution is to use super gum and baking soda. Utilise a sturdy slice of scrap paper-thin that be easily removed later and attach it with tape or a manus clench to aid forbid any fabric from running through the hole. Clasp three or four drops of super glue into the hole to make a pocket-sized puddle. The cardboard volition piece of work as a baking that gives the glue a flat edge. And then, sprinkle a pinch of baking soda on top of the gum and press it downwards firmly. Keep building layers until you've formed a plug that is flush with the top of the hole. Once the hole is plugged, let the patch dry and harden for 15 minutes and then you can remove the paper-thin backing.

• Question

  How do you fix a big hole in plastic?

  

  Drew Hawkins1

  Community Reply

  You can patch the hole with epoxy and fiberglass. Get-go by cut two fiberglass patches vi inches (15 cm) larger than the hole. And so, mix even amounts of each role of the epoxy in a bucket using a stir stick. Information technology should exist very thick and tacky. Employ a putty knife to spread a sparse layer of epoxy on ane side of the hole. Information technology should exist thick plenty that the fiberglass can stick to it, but not overly thick. Press one of the fiberglass patches onto the epoxy, and then paint some other layer of the epoxy over the fiberglass. Let information technology dry out for 24 hours so it hardens and cures. So, repeat the procedure on the other side of the pigsty. In one case both sides accept stale, you lot can sand the epoxy shine and paint over information technology if you like.

• Question

  How do I fix a small pigsty in plastic?

  

  Drew Hawkins1

  Customs Answer

  You can endeavor melting plastic welding rod into the hole to fill up it. Start by sticking a strip of paper-thin over the back of the pigsty to serve equally a backing. Then, agree the plastic rod one⁄two inch (xiii mm) above the hole. Utilise the welder on the end of the plastic rod to cook the plastic into the pigsty. Once the hole is filled, turn off the welder and let the plastic solidify. Then, use a soldering atomic number 26 to trim and smoothen the pigsty then the edges are flush. Wait a few minutes to let the plastic cool and solidify and then use a file or sandpaper to smooth it out.

Ask a Question

200 characters left

Include your electronic mail address to get a bulletin when this question is answered.

Submit

Advertisement

Thanks for submitting a tip for review!

• Use caution as using welders and soldering irons so you don't burn yourself.

• Vesture dispensable gloves when working with super glue or epoxy to forbid whatever irritation.

• Every bit y'all file or sand your plastic, wear a face mask or work in a well-ventilated surface area so you don't breathe in the particles.

Advertising

Things You'll Need

• Paper-thin
• Tape or clamp to agree the backing
• Super glue
• Baking soda
• File or sandpaper

• Cardboard backing
• Tape or clamp to hold the backing
• Plastic welder
• Soldering iron
• Plastic welding rod
• Sandpaper or file

• Fiberglass patches
• two-Part plastic epoxy
• Saucepan or mixing bowl
• Stir stick
• Putty pocketknife

About This Commodity

Commodity Summary Ten

Yous can fill tiny holes in plastic with some super glue and baking soda. Starting time by attaching a slice of scrap cardboard to the backside of the hole to proceed fabric from dripping through. Add together some super gum over the pigsty and then sprinkle a compression of baking soda on peak of the mucilage. Keep adding additional layers and baking soda until the hole is plugged. For larger holes, use fiberglass patches and two-part epoxy. Mix the epoxy together to actuate it, place the patch over the hole, and pigment a layer of the epoxy over the fiberglass. When it's dry, sand the epoxy until it's polish. To larn how to cook plastic rods to fill modest holes in plastic, proceed reading!

Did this summary help you lot?

Thanks to all authors for creating a folio that has been read 94,990 times.

Did this article help you lot?

Source: https://www.wikihow.com/Fill-Plastic-Holes

Posted by: blakelivelyins.blogspot.com

Share this post